Maximum Equipment, Maximum Systems, Maximum Technical Services,Spray Booths, Blowtherm, Global Finishing, Hankinson, Pyrmid, Becca, Garmat, Zonga, Spray Tech, Bleeker Bros, Painting, Spraying, Automotive, Industrial, Prep Stations, Mixing Rooms, Eurovac, Filters, Airflow, Kaiser, Infared, Generating Group, Devilbis, Binks, Service, Refinishing, IRT, RTI, Envirocure, Proclean, High Capacity Spray Booths, Downdraft Design, Ultra XL, Ultra XL insulated, Ultra XL single skin, Pressurized Crossdraft Design, Non-Pressurized Corssdraft Design, Dual Skin, insulation, Make-up systems, Forced Dry, Recirculating Cure, Paint Mixing Rooms, Vestibules, 2-axis, 3-axis painters lifts, Sound attenuation, VOC abatement systems, Control Systems, PLC, monitoring systems, electro mechanical, Planning assistance, installation, Startup, Training, Maintenence, ETL,Three Air Flow Zones, Micro Clean CAF, CAF, COntrolled Air Flow, Doqwndraft Celing Media, Dustlock Adhesive, Expert 2, Expert, Recirculating Downdraft sparybooth, CureTronic, PLC Controls, Pits, Intakes, Exhaust Stacks, Three Row Pits, corner lights, 6-tube, corner lights, lights, motors, motor starters, disconnect switches, limit switches, push buttons, Expert 1, CFM, BTU, Direct Fire Industrial Air heater, Air Heaters, Air heater, Automatic recycle feature, saving fuel energy, Fire supression, variable frequency drives, NFPA-33, NFPA-86, NFPA-91, NFPA-101, NFPA-70, OSHA, IFC, IBC< IMC, BOCA, UFC, UBC, UMC, SBCCI, Code compliance, High efficiency filters, SM 34 High Capacity, Global Filter Media, Polyb, TotalTac, Smart Media, Devilbiss, Air Compressors, Service Kits, Mainencance Kits, Valve disc, Jam & cap nuts, Set screws, Valve springs, Valve gaskets, Series, Filters for compressed air, Separator filter, micron de-soiling filter, high efficiency filter, vapour filter,Universal industrial spray booths, expandable Modular design, Standard air velocites, FPM, filtered entry doors, solid entry doors, filtered intake plenums, crane opening, conveyor openings, air replacment units,Tubeaxial non-sparking exhaust fans, high efficiency TEFC type 3, Phase Multi-voltage electric exhaust fan motor, variable pitch pulleys, manometer, top or rear exhaust outlet, light fixtures, working compartment extensions,control panels, control packages, curtains, custom booths, touch screen controls, yoke style plenum, soilid style plenum, paint pockets, spiral ducts, roof flanges, automatic shutter, fan support frame, fan connector ring, fan motor housing, filtration, open face industrial booths, bench floor, removing airborne paint particles, balanced airflow

Maximum Equipment
Main Office:
5550 Brooks St.
Montclair, California 91763

Phone:

800-318-6508
909-391-5139

Fax:
909-391-5866

E-mail

Custom Designed Ovens Standard Curing or Dry-Off Oven Systems - Designed to meet production requirements with maximum efficiency. Global Finishing Solutions also features an Internal Loop System - featuring air seals to minimize the amount of heated air in the oven escaping to the surrounding atmosphere.

Special Iso-Dynamic High-Velocity Curing Oven — Cut Curing Time up to 70% The process consists of 2 basic components: a heat source and an air distribution system. The heat source is an air heater complete with a gas-fired burner. The burner operates under pressure and is connected to a blower that provides filtered air to the air heater. The heated air is then transferred to the process area through an air distribution system that is a network of ducting and jet pipes.
The ISO-Dynamic Process uses a high-pressure, low volume airflow system, no mechanical re-circulation of air is required. Re-circulation is achieved through internal entrainment. As heated air is ejected through sized orifices in the jet pipes, a consistent turbulence is created in the process area. The impact velocity of the mixed air to the work surface is approximately 800 fpm. Also consider that the heated air has expanded through the heater box and is at a higher volume and lower density. This is referred to as "Soft Air".
The ISO-Dynamic Process provides consistent temperatures and airflows throughout the process work area. Operating temperature range is 100°F to 500°F for standard construction and modular design allows for independent zone control. Multi-pass conveyor arrangements and work opening profiles can be provided to meet customer requirements. ISO-Dynamic ovens are factory assembled and test fired prior to shipment. Shorter Curing Cycles Substantial Fuel Savings Consistent Temperatures Reduced Floor Space Fast Heat-Up
Exclusive In-Line RHT® for Continuous Cleaning Hook — Racks A Custom Designed Option for All High-Production Systems
FAST . . . EFFICIENT . . . Within 4 to 6 Minutes, the Process Heater Removes Paint from Racks and Hooks
Racks and hooks travel through a refractory-lined heated chamber, where air temperature of 1000ºF to 1200ºF ignite the paint, turning it to ash. The hooks and racks are then conveyed to a washer where water cools them, removing most of the ash. To conserve resources, water is re-circulated through the system. An optional filter (Model no. D8RHT) is available for removing excess ash from the water stream. The RHT can either be installed in-line or as a satellite system.